OmegaLand

Support

V3.1 Release Information

The new version of OmegaLand 3.1 has been released.
For more information, see here .



Folder to Store RSView32 Activation File

* The following is our brief description about a part of RSView32(*1)activation.
For its official details, please see the information page of Rockwell below.

(*1) RSView32 is a trademark of Rockwell Software, Inc..


Outline of FactoryTalk Activation:
http://www.rockwellautomation.com/support/activations.page

Folder to store the activation file
  • By default, the folder to store the activation file of RSView32 is
    C:\Program Files\Common Files\Rockwell\Activations
  • The settings of this folder can be checked/set by the FactoryTalk Activation Tool of RSView32.
  • To start the FactoryTalk Activation Tool, click [All Programs] in the Start menu of  Windows - [Rockwell Software] - [FactoryTalk Activation] - [FactoryTalk Activation Tool]. (If these items cannot be found in the menu, it seems that the FactoryTalk Activation has not been installed. Install it with the installation media (CD) of RSView32.)
  • After the FactoryTalk Activation Tool is started, click the [Settings] tab and the folder to store the activation file can be confirmed.

Operation Check of USB Key and Driver Reinstallation in RSView32 Activation

* The following is our brief description about a part of RSView32 activation.
For its official details, please see the information page of Rockwell below.


Outline of FactoryTalk Activation:
http://www.rockwellautomation.com/support/activations.page

Confirmation by FactoryTalk Activation Tool

For activating RSView32 and its continued use, the USB key (dongle) must be recognized by the RSView32. If the USB key is working properly, the LED at its end will shine. In the past, however, there was a case that RSView32 did not recognize the light. For reliable confirmation, perform the following procedures.

  1. To start the FactoryTalk Activation Tool, click [All Programs] in the Start menu of Windows - [Rockwell Software] - [FactoryTalk Activation] - [FactoryTalk Activation Tool]. (If these items cannot be found in the menu, it is seems that the FactoryTalk Activation has not been installed. Install it with the install media (CD) of RSView32.)
  2. After FactoryTalk Activation Tool is activated, click the [Get Activations] tab. Then, click the radio button to select [Use Host ID of a dongle] and click the pulldown selection on the right side of [click to scan --->], which will allow you to obtain the ID of the USB key connected presently.
  3. After the above operation takes place, a message telling that the USB key information is going to be read will appear. Click the and the reading will actually start. The ID obtained will appear in the format of [FLEXID=XXXXX] at the place of [click to scan --->]. Check if it is the same with the value marked on the surface of the USB key. If the USB key cannot be read, an error message will appear and (re-scan) will be displayed in [click to scan --->].
Driver Reinstallation

In case the USB key cannot be recognized, its driver seems to have a problem.
Download the driver (HASP4_driver_setup.zip) from the following page and install it.
http://www.aladdin.com/support/hasp/hasp4/enduser.aspx


OmegaLand: Reinstallation of USB Key Driver

As a cause of unsatisfactory performance of a module in OmegaLand, a poorly recognized USB key may be mentioned. It can be due to the improperly installed USB key driver or a file replaced in the driver. Under such circumstances, there is no need to reinstall the whole OmegaLand, but you may reinstall the USB key driver only.

General Notes
  • When you install or uninstall the USB key driver or any software which is related to OmegaLand, remove the USB key from the USB port. Before you connect the USB key again, be sure that the software is installed and PC is restarted once, and that logon is completed.
  • Connect the USB key to the directly connected or stable USB port of the PC as much as possible; otherwise, the power supply can become unstable.
Driver Reinstallation

Please follow the procedures below to reinstall the driver.

  1. Check the “OmegaLand’s user”. The “OmegaLand’s user” is the logon account who installed the OmegaLand. For more information, see the OmegaLand Installation Manual.
  2. Confirm that the “OmegaLand’s user” belongs to the Administrators. If it does not belong to the Administrators, add it to the group.
  3. Perform logon by the “OmegaLand’s user” which belongs to the Administrators.
  4. Uninstall the Sentinel System Driver (and Sentinel System Driver Installer, if any). Uninstall it on “Programs and Features” on the control panel (or “Add/Remove Programs” in Windows XP). After completing the un-installation, restart the PC.
  5. To execute, double click on install_driver.bat in \sentinel\tool of . ( is the installation destination specified when OmegaLand is installed. By default, it is C:\Program Files\Omega Simulation\Visual Modeler.) Then, the USB key driver will be installed. After completing the installation, restart the PC.

* The above text is our description about a part of reinstallation of the USB key driver.
For its official information, please access the address below.


Download ------ The Latest System Driver
http://www.rainbow.com.my/support.php?id=1&PHPSESSID=2da0c04438b6f53d03c28cdb0076d93a
(See the Sentinel System Driver Installer)